#Configure usb to serial mac how to
#Configure usb to serial mac install
#Configure usb to serial mac driver
#Configure usb to serial mac download
#Configure usb to serial mac windows

You can click on the Advanced button to set the correct modem vendor and model. Now the USB-Serial Controller device is added to the list and you can start to configure the serial modem Internet dial-up settings attached to the PL-2303 cable adaptor. You can also choose to change the Service Name to distinguish the device if you have several devices attached. Select the Interface USB-Serial Controller. If you do not see the USB Serial Controller device, click on the + add button to look for the device. The left side column shows you all the existing ports and status. Go to System Preferences and click on Network. One common test is to connect a 56K serial modem to the PL-2303 adapter.

#Configure usb to serial mac how to

4 of 12 - August 4, 2011ДҐ Using the USB-to-Serial Device under Mac OS X The following steps will show how to use the PL-2303 device under Mac OS X operating system: 1. NOTE: Mac OS may also pop-up a new network interface when it detects a new USB-Serial Controller device.

#Configure usb to serial mac windows

If you try to plug another PL-2303 device, you should also see several tty.usbserialx listed where x is the assigned device number similar to Windows COM port assignment. You can run the Terminal program under Applications-Utilities folder and type the following commands: cd /dev ls tty.usbserial* You should see the tty.usbserial device which means the USB serial device is already setup properly. You can then proceed to check if the USB serial port device is setup properly. This means that the hardware device is detected by your Mac computer. Click USB hardware inside System Profiler and look for USB-Serial Controller or USB-Serial Controller D. You can first run the System Profiler program under the Applications-Utilities folder. After rebooting the system, you can now plug the PL-2303 USB-to-Serial adaptor or cable to the USB port. Close all programs and click Restart to complete installation and reboot the system. At the end of the installation, you will need to restart your computer. Click Continue to proceed and follow the succeeding instructions to complete the installation.

#Configure usb to serial mac driver

Click on the driver installer file to run the driver installation process. Click on the DMG file to extract the driver installer package. The PL-2303 Mac OS X driver package contains the DMG compressed image file.

#Configure usb to serial mac download

Download the Mac OS X Universal Binary driver from Prolific website.

#Configure usb to serial mac install

The driver can be downloaded from the Support webpage of the Prolific website: System Requirement The following requirements are needed: Mac OS X 10.1 to 10.7 operating systems (includes 64-bit support) Also supports Mac OS X Lion 10.7 (see page 12) Apple Mac OS X compatible computers (Intel or PowerPC based machines) USB 1.1 or higher port PL-2303 USB-to-Serial Cable Adapter PL-2303 Mac OS X Universal Binary Driver Mac OS X Driver Installation The following steps will show how to install the PL-2303 device under Mac OS X operating system: 1.

Again, just FWIW.1 PL-2303 USB-to-Serial Bridge Controller Mac OS X Universal Binary Driver Installation Guide Introduction This installation guide document shows the procedure for installing the MacOS X driver for Prolific PL-2303 (H/HX/X) devices. I also ended up modifying the permissions on the lock directory, but there's probably a better way to do that. That's why I compiled it with /var/spool/lock instead. There is no /usr/spool/uucp, or /var/lock, as mentioned in the man page. (of course, that's because my application is to talk to a device at 9600N81, YMMV.)ДЈ) Notice the lock dir mentioned above. configure -enable-dfl-port=/dev/tty.serial -enable-lock-dir=/var/spool/lock -enable-dfl-baud=9600 Here are some of the defaults I compiled into the program: Once this is done, it's easiest to just reboot the machine.Дў) As mentioned above, the serial port is /dev/tty.serial. You might *think* of editing /etc/ttys, but you actually want to edit /System/Library/StartupItems/SerialTerminalSupport/SerialTerminalSupport - and edit the line halfway through to say, Disable this before trying to use the serial port for other purposes. Here are a few things to be aware of re: the serial port.ДЎ) Just like any cisco router or HP switch, etc, the XServe is configured to listen with a secure terminal on the serial port, for config purposes.